OPTIONAL ACCESSORIES:
NEWALL C80 two (2) axis digital readout (installed) . . . . . . . . 1,695.00
NEWALL C80 three (3) axis digital readout (installed) . . . . . . . 2,195.00
MITUTOYO digimatic quill kit (LED readout for spindle). . . . . . . 400.00
SERVO 150 lb power feed unit, longitudinal (installed). . . . . . . 950.00
ALIGN model AL250 150 lb power feed unit, longitudinal (installed). 500.00
SERVO 150 lb power feed unit, cross (installed) . . . . . . . . . . 1,295.00

ALIGN model AL250 150 lb power feed unit, cross (installed) . . . . 750.00
SERVO 140 lb power feed unit, knee vertical (installed) . . . . . . 1,395.00
ALIGN model AL250 150 lb power feed unit, knee vert (installed) . . 750.00
12" rotary table (vertical & horizontal). . . . . . . . . . . . . . 1,200.00
Coolant system (installed). . . . . . . . . . . . . . . . . . . . . 620.00
Chip pan (49" x 30" x 7.5") . . . . . . . . . . . . . . . . . . . . 450.00
Clamping kit (52 piece) . . . . . . . . . . . . . . . . . . . . . . 120.00
R-8 collet set (11 piece, 1/8" to 3/4") . . . . . . . . . . . . . . 155.00
6" angle-lock milling vise. . . . . . . . . . . . . . . . . . . . . 550.00
Horizontal milling attachment (not installed) . . . . . . . . . . . 1,030.00
Automatic air power draw bar (not installed). . . . . . . . . . . . 825.00
T-slot cover. . . . . . . . . . . . . . . . . . . . . . . . . . . . 40.00
6" riser block. . . . . . . . . . . . . . . . . . . . . . . . . . . 580.00
8" riser block. . . . . . . . . . . . . . . . . . . . . . . . . . . 650.00
In-bound freight to Miami, FL (stock machine) . . . . . . . . . . . 1,000.00

ELECTRICS: 220 volt, 3 phase, 60 Hz.

STANDARD ACCESSORIES:
3 HP spindle motor with digital RPM display, analog load meter and
automatic spindle direction reversal when switching between high
and low speed ranges

Table, saddle and knee by hardened and ground dovetail ways
Precision leadscrews with backlash compensating double nuts
Precision bored and ground milling head, with super precision
ABEC-7 bearings
Meehanite casting with built in coolant reservoir in machine base
Centralized one-shot lubrication, with metered check-valves

SPECIFICATIONS:
Size of table (length x width) 9" x 49" (230mm x 1225mm)
Longitudinal travel 35" (875mm)
Cross travel 12" (305mm)
Ram traverse 14.5" (365mm)
Vertical knee travel 15" (390mm)
Quill traverse 5" (127mm)
Quill diameter 3.375" (84mm)
Quill power feed rate--number 3
--range (ipr) .0015/.003/.006
Spindle taper R-8
Main motor 3 HP
Head moves right to left 90 degrees
Head tilts front to back 45 degrees
Spindle speeds--number infinitely variable
--range 60 to 4200 rpm
Net weight (approx.) 2,500 lbs.
Dimensions (L x W x H) 72" x 72" x 84"

A M Metalmaq Inc
320 E 10th Ct Hialeah FL 33010-5151
Tel: 305-883-9200 Fax: 305-883-0660
Email (Request Quote): sales@ammetalmaq.com
Web: www.ammetalmaq.com