To the best of our knowledge all details listed below are deemed correct.
          It is the buyers responsibility to confirm ALL details prior to purchase.
          
          Option: These new machines are being sold as-is with pre-installation checkout
          in Chatsworth, Califonia. Parts Warranty Only Starting at: $10,000.00
          
          Equipped With:
             Heidenhain Glass Scale Feedback on all 5-Axes 
             "Big-Plus" Dual-Contact #40-Taper Spindle
             Chip Wash Down Coolant System 
             300 PSI (20-Bar) "Through-the-Spindle" Coolant System
             Full Machine Enclosure with Top Covers (precut for exhaust duct)
             Spindle Air Blast by M-Code
             Spindle Oil Cooler - Thermostatically controlled
             Remote Operator MPG Hand wheel
             High Speed Synchronous Rigid Tapping
             Dual LED High-Intensity Worklamps
             32GB Solid State Data Server
             32GB USB & SD Memory Card Slots and Ethernet connectivity
             Machine Condition Signal Lamp
             Tramp-Oil Coolant Recovery System
             6-Thru-Tool-Coolant Pull Studs
          
          Axis Travel
             X-Axis:                                34.64"         880mm
             Y-Axis:                                23.62"         600mm
             Z-Axis:                                25.59"         650mm
             Spindle to Rotary Table Surface:       4.72-18.89"    120-480mm
             Spindle Center to Z Way Covers:        22.44"         570mm (Troat)
          
          Tilting Rotary Table
             Platter Diameter:                      12.6"          320mm
             Center Bore Diameter:                  50 H7
             T-slot Width / Number:                 12H7/4
             Guide Block Width:                     18mm
             Maximum Part Swing:                    16.3"
             Maximum Work Table Load:               220 lbs        75kgs
          
          Spindle
             Spindle Motor:                         25 HP S3 Power 20HP 30-Min
          
             Spindle Speed:                         12,000 RPM
          
             Spindle Torque:                        90ft-lb @1,500 RPM
             Tool Type:                             CAT #40 Taper  BT#40 Optional
             Retention System/Holding Capability    BellVille Spring Stack (1650-1760 lbs)
             Spindle Runout:                        <0.000040" TIR
             Spindle Bearings - Rear:               110mm NSK70BNR 2-P4 Class 7 Bearing
             Spindle Bearings - Front:              110mm NSK70BNR 2-P4 Class 7 Bearing
             Retention Knob:                        C40-4502H (Coolant)
          
          Axis Feeds
             Rapid Traverse (X,Y):                  1,417 IPM      36m/minute
             Rapid Traverse (Z):                    1,260 IPM      32m/minute
             Cutting Feedrate:                      0.02-393 IPM   10m/minute
             Axis Drive Motor Power (X,Y,Z):        5-HP           3.5 kw
             Ballscrews (X,Y,Z):                    40mm Ballscrews12mm Pitch
             Least Input Command Increment:         0.0001"/0.000040"0.001mm(40 Millionth)
             Accuracy X,Y,Z Axis (JIS6338):         +0.0002"/12"   +0.005mm Over 300mm
             Repeatability X,Y,Z Axis (JIS6338):    +0.0001"/12"   +0.003mm Over 300mm
          
          Tool Changer
             Tool Capacity (40+1):                  40 Tool Twin ArmChain Drive Rack
             Tool Shank:                            CAT#40 Taper
          
             Tool Change Time:                      1.7 Seconds Tool to Tool
             Tool Diameter / w/adjacent tool:       5.90" / 3.15"  150mm/80mm
             Tool Length/Weight (from gage line):   11.81" / 15 lbs300mm/7Kg
             Tool Selection/Tool Access             Random         Bi Direction: 
          
          General
             Coolant Capacity:                      97-Gallons     256 Liters
             Electrical - Connected Load:           50 amps        220vac+5%, 60hz
             Air Service Requirements:              85 PSI @ 14-scfm
             Machine Dimensions:                    115" x 82" x 116"306x231x256cm
             Machine Weight:                        15,708 lbs     7,120 kg
          
          Built In Tilting Rotary Trunnion Drive System Specifications
             Platter Diameter:                      12.6"          320mm 
             Center Bore Diameter:                  50mm H7
             T-Slot Width:                          12mm H7
             Guide Block Width:                     18mm
             A-Axis Tilting Servo Motor:            Mitsubishi HF-224T
             C-Axis Rotary Servo Motor:             Mitsubishi HF-104T
             Torque:                                7 Kg-cm
             Indexing Resolution:                   0.001 Degrees
             Indexing Accuracy, A / C:              50 Sec/20 Sec
             Indexing Repeatability, A / C:         +4 Sec / +3 Sec
             Feedback System A / C:                 Heidenhain Encoder (ECN-223M w/ 10 sec.
          
                                                    resolution)
             Work Load Capacity:                    165 lbs        75kg Horizontal
             Transmission Ratio A / C:              1:120/ 1:90 
             Tilting Angle Range:                   +30 - -120 Degrees
             Brake Torque A / C:                    140 ft lbs
             Cutting Torque Limit:                  25 Kg/m
             Rotational Speed A / C:                25 / 25 RPM
             Work Load Capacity:                    330 lbs        75kg In Tilt 
          
          
          *Machine Options*
          
             Upgrade to 5-Axis Simultaneous Operation w/ Mitsubishi M850 Control
                                                                   POR
          
          
          Factory machine installation: "Peace-of-Mind Factory Installation" - Includes
          
          Expenses:                                                POR
          
          Factory On-Site 3-Day Machine Operation and Program Training - Includes
          
          Expenses:                                                POR
          
          
          Belt Type Chip Conveyor w/ 38" Barrel Height Discharge:  POR
          
          
          15,000 RPM Spindle Speed Upgrade:                        POR
          
          24,000-rpm HSK-63 Integral Spindle 
          w/ Ceramic Bearings & Spindle Chiller:                   POR 
          
          Second-Year Machine Warranty:                            POR
          
          
          Voltage Stabilizers/Transformers 
          (specify voltage needs):                                 POR
          
          1,000 PSI Through-The-Spindle Coolant Upgrade:           POR
          
          
          
          

Automatics & Machinery Co Inc
150 Martin St Longmont CO 80501-5939
Tel: 800-543-7666 Fax: 303-651-6556
Email (Request Quote): steve@automatics.com
Web: www.automatics.com