"To the best of our knowledge all details listed below are deemed correct. It
          
          is the buyer's responsibility to confirm all details and we encourage an
          
          inspection of the machine(s) and accessories prior to purchase."          
          
          All Information From OEM Brochure Should Be Verifed By Buyer:
          
          Equipped With:
          This machine has the following options:
          
          Genturn SL-42Y2 Grand Package:
             Purchased as a Non-Guide Bushing machine with Chucker Kit**
             With Edge Patriot 551 12' Barloader - 
             MistBuster 850 Mist Collector
             1,000 PSI MP-Systems 4-Port High Pressure Coolant System (2,000 PSI @ pump
             Harbor Spinflo Coolant Chiller
             Part Chute
             Parts Conveyor
             Chip Conveyor & Chip Cart-link-belt style 
          
          ** Synchronous Rotary Guide-Bushing Option ..........$6,995.00
          
          
          Standard Features
             Mitsubishi M830 CNC control with 8-axis simultaneous motion
             19-Main-Spindle Tool Holders (33-Total standard Tool Holders) 
             14-Sub-Spindle Tool Holders (33-Total Standard Tool Holders) 
             Sub-Spindle Programmable Cutting Oil Flush
             Parts catcher and finished parts conveyor 
             "Dead-Length" Traub-42 / 173E Collet Systems for Both Main & Sub Spindle
             Cutoff confirmation sweep-arm switch 
             Collet Chuck for both main and subspindle with Hydraulic Actuators
             Non-Guide-Bushing Collet Holder for 42mm Barstock 
             18,000 BTU Oil Chiller System Installed
             Sub-spindle programmable air blast and Finished Parts Ejector
             High-Performance "C"-Axis on both the main and subspindle 
             Rigid Synchronous Tapping
             10-Horsepower Integral "Beltless" Main & Sub Spindle Motors
             Spindle Chiller for Main & Sub-Spindle Temperature Control 
             1-3/4-Horspepower Coolant Pump, w/ double coolant filtration 
             Coolant flow confirmation monitoring switch with fault interrupt interface
             9-live-tools: 6-ER-20 & 3-ER-16 collet spindles, work area illumination 
          
          
          Specifications:
          
          MAIN SPINDLE WITH FULL C AXIS:
          Maximum RPM / spindle bearing:      6,000 RPM (5-bearing spindle, 3-front, 2-
          
          rear ball bearings) 
          
          Main Spindle
          Main Spindle Servo Motor:           10-HP 15 Min Duty Rated (7.5HP Constant)
          
          Collet Style; main & sub-spindle:   Traub 42 / 173E
          Guide Bushing Type:                 Optional Rotary Guide Bushing
                                              (Uses Hardinge STM38 Bushings)
          Bar Diameter W/ or W/O GB:          w/ GB 38mm; and w/o GB 1 5/8" (42mm)
          Turning Length (Rotary):            12.20" Single Stroke (310mm)
          Turning Length (Without Bushing):   4.13" (105mm)
          
          MAIN SPINDLE TOOLING:               17-Tool Holders - (30 Standard Total) 
          O.D. Turning Tool Holders-S1:       (6) 16mm square shank turning tool holders
          I.D. Internal Tool Holders-S1:      (5) 25mm Shank Round Tool Sleeve Bores
          I.D. Deep Hole Drill Positions-S1   (2) 25mm Shank Round Tool Sleeve Bores
          Cross slide live tools-S1:          (6) ER-20, 4,000 RPM, 2.0 HP (1.6kw) 
          Axial front slide live tool opt.S1: (3) ER-20 - Opt. in Lieu of 1 Cross Tool
          Maximum Drilling/Tapping Capacity:  13mm Drilling/M10 Tapping 
          Cross Drilling / Tapping Capacity:  10mm Drilling/ M6 Tapping 
          
          SUB SPINDLE WITH FULL C AXIS:       Simultaneous Main/sub
          Sub spindle RPM / spindle bearing:  6,000 RPM/4 Bearing - Quad-Duplex 
                                              pair configuration
          Sub Spindle Servo Motor (5.5/7.5kw) 10-HP, 15 Min Duty Rated (7.5HP Constant)
          
          Barstock Diameter:                  1-5/8" (42mm); 42mm thru sub-spindle 
          Finished Parts Ejector & Air Blast
          Max workpiece length/front eject'n  110mm from Sub spindle
          SUB-SPINDLE BACK-WORKING TOOLING:   14-Tool Holders 
          O.D. Turning Tool Holders-S2:       (3) 16mm Square Shank Turning Tool Holders
          I.D. Internal Tool Holders-S2       (5) 25mm Shank Round Tool Sleeve Bores
                                              shared with main spindle
          I.D. Internal Tool Holders-S2 
             Upto 8:                          (3) ER-16 Fixed Tools - 3/8" Max
          Subspindle axial live tools-S2
             Upto 8:                          (3) ER-16 Axial Live Tools 4,000 RPM/ 1 HP
             (8-subspindle tool block can mix live & fixed tools, or 2 radial live tools
             can be substituted for 2 axial tools on subspindle tool block)
          Drilling/Tapping Capacity:          13mm Drilling / M10 Tapping on Sub
          Cross Drilling/Tapping Capacity:    8mm Drilling / M6 Tapping 
          
          AXIS:
          Main Spindle Stroke                 12.20" (310mm)
          X1, Y1, Z1, X2, Y2, Z2 Rapids       944 IPM (24m/minute)
          X1, Z1 Axis Motor Power             2-Horsepower (1.4kw)
          X2, Y1, Y2, Z2 Axis Motor Power     1-Horsepower (.75kw)
          Linear Ways - X1, Y2                Ball-Bearing Linear Ways (point contact)
          Linear Ways - X2, Y1, Z1, Z2        Roller-Bearing Linear Ways (line contact -
                                               twice as rigid)
          Minimum input unit                  0.0001" (0.001mm = 40 millionths inch)
          
          MACHINE SPECIFICATIONS:
          Machine Dimensions (L x W x H):     121" x 67" x 83" (2925 x 1690 x 2100 mm)
          
          Machine Weight:                     11,024 lbs (5000kgs) 
          Machine Power Requirements:         220vac, 75 Amps, 30kva, 3-Phase, 60hz
          Air Requirements:                   85-PSI @ 6-CFM 
          
          
          

Automatics & Machinery Co Inc
150 Martin St Longmont CO 80501-5939
Tel: 800-543-7666 Fax: 303-651-6556
Email (Request Quote): steve@automatics.com
Web: www.automatics.com