MACHINE# 13355
          
          1.TECHNICAL SPECIFICATIONS:
          NEW ELECTRIC CONTROL SYSTEM (DC MOTORS CONTROL & PLC PANEL)
          NEW ENTRY DEGREASING SYSTEM
          NEW FURNACE BURNER CONTROL SYSTEM
          MATERIAL : STAINLESS STEEL 300, 400
          THICKNESS : 0.01" ~ 0.105" (0.254mm - 2.667mm)
          COIL WIDTH :
           24" (610mm) MAXIMUM, 12" (305mm) MINIMUM - 0.050" (1.27mm) THICKNESS
           12" (305mm) MAXIMUM, 6" (152mm) MINIMUM - OVER 0.050" (1.27mm) THICKNESS
          COIL WEIGHT : 12,000 LBS. (5443 KG) MAXIMUM
          COIL DIAMETER : O.D. 60" (1524mm) MAXIMUM , I.D. 16" & 20" (406mm & 508mm)
          LINE SPEED : 9 FPM MINIMUM ~ 90 FPM MAXIMUM (2.75-27.5M/MIN.)
          SPLICING SPEED : 10FPM to 30 FPM (ADJUSTABLE) (3-9.1M/MIN.)
          AIR SUPPLY : 80 PSI
          ELECTRIC SUPPLY : 3PHASE 220V 60CYCLE
          MAKER : HERR EQUIPMENT CORPORATION U.S.A.
          
          2.LINE FLOW
          
          3.PAYOFF REEL
          COIL WEIGHT: 12,000 LB. (5443 KG) MAXIMUM
          COIL DIAMETER: I.D. 16" ~ 20" (406mm - 508mm), O.D. 60" (1524mm)
          COIL WIDTH: 24" MAXIMUM  6" (152mm) MINIMUM
          COIL CAR LIFTER STROKE: 27-1/2" (700mm)
          REEL TRAVEL TOTAL: 48" (1220mm)
          DRUM: EXPANDED 20-1/2" (520mm), COLLAPSED 15" (380mm), FACE 28" (712mm),
          
          ROTARY CYLINDER 8" BORE 6-1/4" STROKE
          BACK TENSION AIR BRAKE
          REEL DRIVE AC MOTOR 3PH-60HZ-220V/440V-1,800RPM
          SNUBBER ROLL (HOLDDOWN ROLL): ROLL O.D. DIA. 6" (152mm) x L 13" (330mm),
          
          AIR CYLINDER 8" (203mm) BORE 9" (228mm) STROKE
          PAPER WINDER AIR SHAFT: EXPANSION TYPE
          DRIVE VS MOTOR 3.7KW-AC220V/380V-4P-60HZ-1,660RPM
          
          4.ENTRY PASS LINE ROLL (DEFLECTOR ROLL)
          ROLL SHAFT: DIA. 2-15/16" x L 46-1/2"
          ROLL COVER:  DIA. 31-1/2" x L 30"
          MATERIAL OF SLEEVE: NEOPRENE
          
          5.ENTRY SHEAR
          
          6.SPOT WELDER
          MODEL: W-2 SCR
          LINE VOLTAGE: 1 DIA. 440VAC 50/60HZ
          WATER FLOW: 6L/MINIMUM
          THYRISTOR SIZE: E SIZE
          MAKER: CHOWEL CORPORATION
          
          7.DEGREASING SYSTEM
          SPRAY CLEANING ZONE : 185 LITER, NOZZLE x 40 PCS., SPRAY PUMP 10HP
          SPRAY BRUSHING ZONE : BRUSH ROLL DIA. 174 x L 750mm x 2 SET, DRIVE MOTOR 1HP
          
          580RPM
          SPRAY SQUEEZING ZONE : SQUEEZE ROLL DIA. 89.1 x L 800mm x 2 EA.
          SPRAY RINSE ZONE : NOZZLE x 32 PCS, SPRAY PUMP 3HP , CAPACITY 220 LITER
          RINSE BRUSHING ZONE : BRUSH ROLL DIA. 174 x L 750mm x 2 SET, DRIVE MOTOR 1HP
          
          580RPM
          RINSE SQUEEZING ZONE : SQUEEZE ROLL DIA. 89.1 x L 800mm x 2 EA.
          AIR CUTTING : RING BLOWER 6.1M3/MINIMUM 3000mmAq, NOZZLE x 22 PCS
          HOT AIR DRY: TURBO BLOWER 15HP 150M3/MIN. 200mmAq, ELECTRIC HEATER 5KW x 2 EA.
          VACUUM DISTILLING RECOVERY SYSTEM : DISTILLING CAPA 150 L/HR., HEATER 24KW
          
          8.ENTRY NO.1 CPC (MANUAL)
          
          9.ENTRY BRIDLE ROLL
          2-ROLLS 
          ROLL SHAFT DIA. 2 15/16" x L 46 1/2", ROLL COVER DIA. 31 1/2" x L 30" NEOPRENE
          DRIVE DC MOTOR 3HP 240VDC 11A 1750RPM
          
          10.ENTRY ACCUMULATOR 
          MAXIMUM CARRIAGE 11'-9" (CYLINDER FULL EXTENDED)
          ROLLS:
           CARRIAGE ROLL x 3 EA.
           SUPPORT ROLL x 4 EA.
           ROLL DIA 31 1/2", 2'-6" FACE
          AIR CYLINDER: ROD 12" DIA x 70-1/2" STROKE x 2 EA.
          AIR SUPPLY 80 PSI
          
          11.ENTRY No.2 CPC (AUTO)
          24" STEERING ROLL DIA. 31 1/2" DIA 30" FACE
          NORTH AMERICAN CENTER GUIDE REGULATOR INCLUDING:
          HYDRAULIC RELAY: H-1013-07B-113
          MOVING COIL: H2503-070-04
          POSITIONING KNOB: H-5410-200-01
          NEEDLE VALVE: H-915-20-302 3/8"
          MANUAL SHUT OFF VALVE: H-915-33-300
          POWER PACK: H-6017-030-13
          CENTER GUIDE DETECTOR: H-3046
          FEED BACK TRANSDUCER
          STEERING ANGLE: +/-40o
          HYDRAULIC CYLINDER
          
          12.FURNACE
          MAKER : ELECTRIC FURNACE U.S.A
          TYPE : MUFFLE TUBE FURNACE
          MUFFLE : INCONELL 601, OVERALL LENGTH 58'-8.1/2", DIAMETER I.D. 2'-8.1/8",
          
          O.D.(2'-8 1/2") + (7/8" x 2) CORRUGATION TUBE
          CARBON ROLLS: SHAFT 9'-3/4" OVERALL LENGTH 5.085" DIA, CARBON SLEEVE: L 2'-9"
          
          x DIA. 4" DIA x 5 EA., MATERIAL RA330, ROLL DRIVE DC MOTOR 0.4KW 230VDC
          
          1750RPM x 5 SET
          FURNACE CHAMBER : IN DIAMETER 4'-9" x OUT DIAMETER 6'-8" x OVERALL LENGTH 55'"
          BURNERS : LNG BURNER 8 EA./Zone x 5 Zone = 40 EA., LNG MAIN 8,500 C.F.H
          ATMOSPHERE : NITROGEN + HYDROGEN
          
          13.COOLING ZONE
          WATER COOLING SECTION
          JET COOLING SECTION: PIN COOLER x 3 SET
          COOLING FAN INVERTER MOTOR 25KW 440VAC 1750RPM x 3 SET
          
          14.CENTER CPC
          24" STEERING ROLL DIA. 31 1/2" DIA 30" FACE
          NORTH AMERICAN CENTER GUIDE REGULATOR INCLUDING :
          HYDRAULIC RELAY : H-1013-07B-113
          MOVING COIL : H2503-070-04
          POSITIONING KNOB : H-5410-200-01
          NEEDLE VALVE : H-915-20-302 3/8"
          MANUAL SHUT OFF VALVE : H-915-33-300
          POWER PACK : H-6017-030-13
          CENTER GUIDE DETECTOR : H-3046
          FEED BACK TRANSDUCER
          STEERING ANGLE : +/-40o
          HYDRAULIC CYLINDER
          
          15.LINE SPEED BRIDLE ROLL
          UPPER ROLL 31 1/2" DIA x 30" FACE
           DRIVE 2HP 240VDC 1750/3000RPM, REDUCER 1/195
          LOWER ROLL 31 1/2" DIA x 30" FACE
           DRIVE 2HP 240VDC 1750/3000RPM, REDUCER 1/195
          SNUBBER ROLL 8" DIA x 6" FACE
          
          16.EXIT ACCUMULATOR
          MAXIMUM CARRIAGE 11'-9" (CYLINDER FULL EXTENDED)
          ROLLS:
           CARRIAGE ROLL x 3 EA.
           SUPPORT ROLL x 4 EA.
           ROLL DIA 31 1/2", 2'-6" FACE
          AIR CYLINDER: ROD 12" DIA x 70-1/2" STROKE x 2 EA.
          AIR SUPPLY 80 PSI
          
          17.TENSION BRIDLE ROLLS
          No.1 T.B.R. 31 1/2" DIA x 30" FACE
           DRIVE 3HP 240VDC 1750/3000RPM, REDUCER 195:1
          No.2 T.B.R. 31 1/2" DIA x 30" FACE
           DRIVE 3HP 240VDC 1750/3000RPM, REDUCER 195:1
          No.3 T.B.R. 31 1/2" DIA x 30" FACE
           DRIVE 2HP 240VDC 1750/3000RPM, REDUCER 195:1
          SNUBBER ROLL 8" DIA x 6" FACE x 2 EA.
          
          18.EXIT SHEAR
          KNIFE 38" LENGTH, OVER LAP 1/8", CLEARANCE +/- 0.0005"
          AIR CYLINDER 10" BORE 6 3/4" STROKE
          
          19.EXIT PASS LINE ROLL (DEFLECTOR ROLL)
          31 1/2" DIA x 30" FACE, ROLL COVER NEOPRENE
          
          20.TENSION REEL
          COIL WEIGHT: 12000 LBS. (5443 KG)
          COIL DIA O.D.: 60", I.D. 20"
          MATERIAL WIDTH: 24" MAXIMUM 6" MINIMUM
          LINE SPEED: 9 TO 90 FPM
          DRUM: 20" EXPANDED, 19 1/2" COLLAPSED, ROTARY CYLINDER 8" BORE 9" STROKE
          REDUCER : OVERALL RATIO MOTOR TO MANDREL 118.3/1
          REEL TRAVERSE CYLINDER: 6" BORE 8" STROKE FOR E.P.C. (AUTO)
          REEL DRIVE DC MOTOR 40HP 240VDC 2200RPM
          COIL CAR LIFT CYLINDER: 6" BORE 27 1/2" STROKE HYDRAULIC CYLINDER
          COIL CAR TRAVERSE CYLINDER: 5" BORE 45" STROKE HYDRAULIC CYLINDER
          
          21.EXIT HYDRAULIC SYSTEM
          OIL TANK 60 GAL.
          MOTOR 10HP 1200RPM
          PUMP QGH12&QGH5 650 PSI LOW PRESSURE, 750 PSI HIGH PRESSURE
          HEAT EXCHANGER IN WATER
          
          22.ELECTRIC SYSTEM
          DC MOTOR THYRISTOR PANEL (EUROTHERM 590P) x 6 SET
          MAIN OPERATION PANEL (IN HMI COMPUTER AND PLC SYSTEM) x 2 SET
          DEGREASING SYSTEM CONTROL PANEL x 1 SET
          FURNACE TEMPERATURE CONTROL PANEL x 1 SET
          
          23.SPARE PARTS
          JET COOLER PIN TUBE: 295 x 1000 x L 1570 x 1 EA.
          UNIVERSAL JOINT: DIA. 200 x L 750 x 3 EA.
          HYDRAULIC CYLINDER: DIA. 50.8 x 200 STROKE x 1 EA.
          ROTARY CYLINDER: DIA. 38 x L 2640 x 3 EA.
          GRUNDFOS PUMP A452504P10336 x 1 EA.
          
          EquipmentRemarks
          20-HI ZR MILL (REVERSING)Running
          4-HI ROLLING MILL (NON REVERSING)Stored - dismantled
          BRIGHT ANNEALING LINERunning
          26" SKIN PASS MILLRunning
          15" SKIN PASS MILLStored - dismantled
          15" SLITTER LINEStored - dismantled (no electrics)
          TENSION LEVELLING LINERunning
          WITH SPARE PARTS Including all drawings
          
           ** SPECIFICATIONS SUBJECT TO REVISIONS **
          
           ** SPECIFICATIONS SUBJECT TO VERIFICATION BY PURCHASER **
          
           ** PRICE QUOTED AS IS WHERE IS SUBJECT TO PRIOR SALE **
          
          
          

Machinery International Corp
20 Commerce Dr North Branford CT 06471-1250
Tel: 203-484-0400 Fax: 203-484-4499
Email (Request Quote): sales@machyintl.com
Web: www.machyintl.com