MACHINE# 13051
          
          SPECIFICATIONS:
          
          This Sendzimir Mill ZR 19-25 12-HI Rolling Mill for stainless steel is now in
          
          storage. The Mill is for the most part complete. Some component parts to be
          
          modernized or supplied by the Purchaser are noted herein.
          
          Operation:  Reversing Cold Rolling 12-HI Sendzimir Mill
          
          Material:  Stainless Steel 200,300,400 Series
          
          Strip Width:
           Entry: 457.2 (18 in.) to 635mm (25.0 in.)
           Exit:  457.2 (18 in.) to 635mm (25.0 in.)
          
          Strip Thickness:
           Entry:  0.5mm (0.020 in.) Can be higher
           Exit:  0.025mm (0.001 in.) to 0.7mm (0.028 in.)
           At minimum thickness of 0.025mm, the strip width should be at least 457.2mm
          
          Coil Weight:  2950 kg (6500 lb.) max.
          Coil O.D.:  900mm (40 in.)
          Coil I.D.:  406mm (20 in.)
          
          Mill section:  ZR 19-25
          
          Mill Speed:  0/50/150 MPM (0/150/450 FPM)
          Line Direction:  Left to right
          Mill Power:  150 HP @ 0/575/1150 RPM
          Winder Power:  100 HP @ 0/350/1400 RPM
          Winder Tension Maximum:  16500 lb. to 200 FPM
          
          Minimum Tension:  8250 lb. to 450 FPM
          Tension Range:  20:1
          Coolant System:  Mineral Oil lube/Coolant
          Power Supply:  6000 (Primary) / 380VAC, 3 Ph., 50 Hz, 220VAC, 1 Ph., 50 Hz
          
          Floor Type Coil Car:  2 x Available
          
          Coil Weight:  3181 kg (7000 Lbs.)
          Width:  25" (635mm)
          O.D.  40" (1016mm)
          
          Lift Stroke:  24" Approximate
          Traverse:  2 meters
          Pump Unit:  5 HP, AC
          
          Application: Then entry coil car is designed to receive and store coils from
          
          either lift truck or overhead crane. Car positions coil on the payoff mandrel.
          
          PAY OFF UNIT: To be supplied by the Purchaser.
          
          Paper winder and drive is supplied and mounted on the base - 2 Available
          
          Left Winder Stand (TUB) and Base - 2 Available
          
          Left Tension Reel w/multiple 100, 150 HP DC motors and gear boxes available
          
          .Strip Entry Encoder - 2 Available
          
          Entry Thickness Gauge - X-Ray
           Two hydraulically operated housings available.
           AM241 isotopes removed.
          
          Mill Housing - Available
          
          Specifications as previously installed:
          
          Mill Type: Sendzimir Reversing 12-HI Mill
          
          Work roll diameter:  40.0248mm (1.812 in.)
          Roll face Length:  660.4mm (26 in.)
          Drive Roll diameter:  104.775mm (4.125 in)
          Backing bearing diameter:  76.2mm (3 in.)
          Lubrication:  Mineral Oil 
          Mill housing:  Forged alloy tool steel
          
          Input Power:  3 x 150 HP @ 0/300/900/RPM
          Mill Speed:  0/50/150 MPM (0/150/450 FPM)
          Maximum tension:  16500 lb. to 200 FPM
          Minimum Tension:  8250 lb. to 450 FPM 
          
          Mill Rolls - Not Available
          Rolls are forged alloy steel, hardened and ground.
          Backing Assemblies: Not Available
          Backing assemblies are the Sendzimir binocular design on the "A", "B", and "C"
          
          backing assembly shafts.
          
          Backing Bearings - Not Available - to be supplied by Purchaser
           Number of Bearings:  24 (3 per shaft)
           Bearing manufacturer:  Timken or equivalent
          
          Strip Sprays - Not Available - to be supplied by Purchaser
          Strip sprays are located on both sides of the mill; both above and below the
          
          strip pass line. The sprays in each quadrant include recessed nozzles. In
          
          addition to providing maximum heat extraction, the "spray boards" help guide
          
          the strip through the mill and protect the intermediate rolls and backing
          
          assemblies from damage by broken strip.
          
          Mill Base available with mill housing
          
          Automatic Gauge Control - Available
          
          Complete operator panel with AGC computer/hardware and gauge control computer
          
          has been recently purchased (new) from I2S (USA). Includes complete operator
          
          desk. It will require some additional work to be fully operational.
          
          Coolant/Lube System - Not Available - to be supplied by Purchaser
          Original system schematic drawings are available.
          
          Specifications of Coolant System:
           Type of Oil: Mineral Oil
           Viscosity:  70-90 SSU
           Total Tank capacity:  3000 G
           Spray pumps:  Two (2) one operating, one standby 10 HP
           Filter system pumps:  Two (2), 10 HP
           Clarity:  1 Micron
          
          New SCR Electrical Drives to be supplied by Purchaser
          
          
               **PRICE QUOTED AS IS WHERE IS SUBJECT TO PRIOR SALE**
          
          **ALL SPECIFICATIONS ARE SUBJECT TO VERIFICATION BY PURCHASER**
          
          
          

Machinery International Corp
20 Commerce Dr North Branford CT 06471-1250
Tel: 203-484-0400 Fax: 203-484-4499
Email (Request Quote): sales@machyintl.com
Web: www.machyintl.com