SERIAL NO. PP-453
TUBE MATERIAL: ZR-2 TUBING, COPPER OR ALUMINUM
TUBE SIZE RANGE: 5" MAX OD (PER MFG. SPECS)
2" MIN OD (PER MFG. SPECS)
3/8" MAX WALL
CAPACITIES:.
DIE ADVANCE - RATED: 150,000 LBS AT 1949 PSI
DIE ADVANCE - MAXIMUM: 192,400 LBS AT 2500 PSI
CLAMP HOLDING: ADJUSTABLE UP TO MAX
475,000 LBS AT 5000 PSI
SPEEDS:
DIE ADVANCE : 79.6 IPM AT 2000 PSI
DIE RETURN: 172.0 IPM AT 1000 PSI
CLAMP ADVANCE: 68.1 IPM @ 1000 PSI
CLAMP RETURN: 114.3 IPM AT 1000 PSI
DIE HOLDER: SINGLE "U" SHAPED
OPEN TOP CAVITY TO
ACCEPT ROUND CASE
POINTING DIES
CYCLES:
AUTOMATIC ONE PUSH
SEMI-AUTOMATIC TWO PUSH WITH MANUAL DIE CHANGE
POINT LENGTH ADJUSTABLE TO 14" MAX. (PARALLEL SECTION)
METHOD OF KEEPING
POINT STRAIGHT: PATENTED AIR CYLINDER
OPERATED CONICAL POINT FOLLOWER
DIE CROSSHEAD TRAVEL. 18"
JAW SIZE - PER HALF . 3-7/8" TK. X 6-3/8" WIDE X 18" LG.
HARDENED STEEL FOR 3.75" O.D. TUBE
METHOD OF CHANGING DIES: MANUAL - APPROX 40 LBS
FOR 8" OD DIE
METHOD OF CHANGING JAWS: MANUAL - APPROX 65 LBS
PER HALF
MAX. OPENING BETWEEN JAWS: 3-3/4"
CLAMP MECHANISM: DIRECT ACTING HYDRAULIC CYLINDER

HYDRAULIC PUMPS:
CLAMP & PUSH VICKERS VANE TYPE
26.5 GPM AT 2000 PSI AT 1200 RPM
CLAMP SEALING: OILGEAR PISTON TYPE
1.72 GPM AT 5000 PSI AT 1200 RPM
HYDRAULIC RESERVOIR: 150 GALLON CAPACITY
HYDRAULIC FLUID: PETROLEUM OIL
150-315 SUS AT 100 DEGREE F

HYDRAULIC PUMP DRIVE MOTOR: 50HP, 1200 RPM, 460 V.,
3 PH., 60 HZ., DOUBLE SHAFT,
TEFC, FR. 365T

HYDRAULIC PUMP DRIVE
MOTOR STARTER: SIZE 3, FULL VOLTAGE COMBINATION
WITH FUSED DISCONNECT IN NEMA 12 ENCLOSURE
METHOD OF LUBRICATING TUBE END
TO BE POINTED: MANUAL
OIL COOLER: WATER TYPE WITH AUTOMATIC
TEMPERATURE CONTROL
MAIN POWER SUPPLY: 460 V, 3 PH, 60 HZ
CONTROL POWER: 120 VOLT, SINGLE PHASE
FROM TRANSFORMER SUPPLIED
CONTROL LOGIC: PROGRAMMABLE CONTROL
IDLER ROLLER LOAD/UNLOAD STAND
NUMBER OF SUPPORT ROLLS: 12 ON APPROX. 60" CENTERS
TYPE OF ROLL : "V" SHAPED URETHANE
ROLL IDLE ROTATION.: 1-1/2" ANTI-FRICTION BEARING
ON EACH SIDE OF ROLL
ROLL SUPPORT & VERTICAL ADJUSTMENT: INDIVIDUAL PIVOT
MOUNTING OF EACH ROLL WITH

INTERCONNECTING
PULL BAR ADJUSTED BY MANUAL
HANDWHEEL ON SCREW JACK
VERTICAL ADJUSTMENT RANGE
OF ROLLS: TO ACCOMMODATE FROM
2" MIN. TO 5" MAX. O.D. TUBES
ESTIMATED EQUIPMENT SHIPPING WEIGHTS:
POINTER: 15,000 LBS
HYDRAULIC PUMPING UNIT: 3,000 LBS
LOAD/UNLOAD STAND: 7,000 LBS
TUBE GRIPPER JAWS FURNISHED:
ONE ( 1) PAIR SINGLE SIDED: 3.675"
DIES FURNISHED: 3.375" & 3.100"

**PLEASE NOTE MANUFACTURERS SPECIFICATIONS**
**TEMPORARY SPECIFICATIONS SUBJECT TO REVISIONS**
**PRICE QUOTED AS IS WHERE IS SUBJECT TO PRIOR SALE**
**ALL SPECIFICATIONS ARE SUBJECT TO BUYER VERIFICATION**

National Machinery Exchange
158 Paris St Newark NJ 07105-3833
Tel: 973-344-6100 Fax: 973-589-0944
Email (Request Quote): sales@nationalmachy.com
Web: www.nationalmachy.com